Integral LED IP33 handleiding

Integral LED IP33

Bekijk hier de Integral LED IP33 handleiding. Het bekijken en downloaden van deze Lamp handleiding is geheel gratis.

Merk
Integral LED
Model
IP33
Product
Lamp
EAN
5055788227410
Taal
Engels
Bestandstype
PDF
Flexible 24V INTEGRAL LED RGB Strip IP33
Installation Guide
IMPORTANT NOTICE
This product should be installed according to the instructions in this guide and by a qualied electrical installer.
All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable
regulations and laws in the country in which it is being installed. This product falls under a low voltage Class III circuit category.
Switch OFF power at the mains before installing the LED strip
Strip must only be installed indoors, in a dry area
Avoid looking directly at the strip when turned on, for a long period of time
Observe the operating temperature of the LED strip: -25C to +60C
To avoid any damage to the LED strip or driver;
Always disconnect or switch o the power supply before cutting or connecting an LED strip. Wait at least one minute before connecting to a recently
powered driver.
Always handle the LED strip with care.
Observe the correct polarity for 24V connections (g 1).
Safely route and secure all wires so they cannot be pinched or damaged
Do NOT power the strip whilst in its packaging reel
Do NOT twist the LED strip or touch the LEDs on the strip surface
To avoid damage or malfunction, Do NOT coat the LED strip with paint, varnish or similar.
INTRODUCTION
This installation guide is for exible, IP33 constant voltage self-adhesive LED strips produced by Integral LED.
Depending on your installation, you can purchase optional or additional accessories such as mounting clips and connectors.
A) CHOOSING A 24V LED DRIVER
This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage
outputs.
The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage
rating) must be at least 20% higher than the total required wattage of the strip(s) being powered.
For example, if you are installing 5 LED strips of 1M each and the power requirement of each 1M strip is 3W/metre – the total power requirement is 15W.
The power rating of the driver should be a least 20% above 15W i.e. A minimum of 18W .
B) PRE-INSTALLATION GUIDE
LED strips make a great addition to any domestic or commercial environment. They can change the mood and look of a space instantly and are very energy
ecient. The possibilities are endless so the requirement for each lighting project will be dierent.
It is worth taking some time to plan your project for the desired eect before removing the backing tape on the LED strip. The specication, length, mounting
position and distance from an object determines the appearance of a lit LED strip. You will also need to consider the placement and concealment, of the 24V
LED driver, control unit and wires, and the power switch to turn the LED strip ON and OFF.
We recommend that you test the strip by temporarily holding the LED strip in place by using a suitable tape, such as masking tape. Safely connect the power
supply - you can then carefully move the strip to try dierent angles and positions to gain the desired illumination eect and position. Check for light spots,
reections and shadows.
Please consider the surface you are applying the LED strip to; the surface should be stable, clean and smooth. On removal of a xed LED strip - damage to
paint, wallpaper or other substrates may occur. Take care in measuring the length required before cutting the strip, take into account the space required for the
connector. You may also consider using a spirit level, plumb line or other guide if required.
In the bag
1 X 5M ±5cm IP33 INTEGRAL LED RGB STRIP on reel pre-tted with an appropriate
connector to connect to a suitable control unit and power supply.
Accessories For IP33
1 X Clip-on strip connector
If you cut the strip into two pieces, you can use this connector to power the remaining
portion of the strip.
IP33
ILSTRGBA_24V_V2
WARNING
DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.
THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.

Vraag over de Integral LED IP33?

Wanneer u een vraag heeft over de "Integral LED IP33" kunt u die hier stellen. Zorg voor een duidelijke omschrijving van uw probleem zodat andere gebruikers en/of de redactie u van een passend antwoord kunnen voorzien.

Koop gerelateerde producten:

Product specificaties

Lampen
Soort lamp LED
Aantal lampen 300
Geïntegreerde LED yes
Levensduur lamp 13000
Design
Soort Universal strip light
Internationale veiligheidscode (IP) IP33
Ondersteuning voor plaatsing Binnen
Beschermingsklasse III
Kleur van het product Wit
Materiaal Polycarbonaat
Op maat snijden yes
Soepelheid yes
Energie
Operating voltage   24 V
Type stroombron DC
Prestatie
Certificering CE, RoHS
LVD
IEC 62031
Kleur licht Multi
Dimbaar yes
Stralingshoek 115 °
Aantal kleuren -
Geschikt voor soort licht Ambiance
Van kleur veranderend yes
Montagewijze Plakband
Gewicht en omvang
Lengte 5 mm
Breedte 10 mm
Gewicht   140 g
Eisen aan de omgeving
Temperatuur, in bedrijf -25 - 60 °C
Verpakking
Breedte verpakking 180 mm
Aantal per verpakking 1
Diepte verpakking 11 mm
Hoogte verpakking 205 mm
Ergonomie
Op afstand bedienbaar yes