SoundBot SB270 handleiding

SoundBot SB270

Bekijk hier de SoundBot SB270 handleiding. Het bekijken en downloaden van deze Headset handleiding is geheel gratis.

Merk
SoundBot
Model
SB270
Product
Headset
Taal
Engels
Bestandstype
PDF
1
2
3Charge headset for at least 3 hours.
(via MicroUSB)
- Red LED will light up when charging.
- Red LED will be o once fully charged.
- Be sure headset is powered o before
going to next step.
Pairing your SB270 via Bluetooth.
- Press and hold the multifunction key for 7
seconds until blue and red lights ash.
- Enable the Bluetooth function on the mobile
phone or computer or other pairing device.
- Search for Bluetooth devices from your
pairing device (phone, tablet or PC).
- Select “SB270” and connect. A beep will
conrm successful pairing.
Power on: 3 rapid blinks of blue light
Power o: 3 rapid blinks of red light blinks
Standby: blue light blinks once every 5 seconds
Incoming call: quick continuous blinks of blue light
In use: blue light blinks once every 5 seconds
Charging mode: red light stays on or blinks
Fully charged: red light will be turned o
Low battery alarm: red light blinks once every 30 seconds
LED Indicators
SENSORY TOUCH CONTROL
Voice Dialing
- Double click the multifunction button
(Note: Your phone must support this function)
Touch Controls (one notch per swipe)
- Pause/Play music: Touch the middle of headphone
and press lightly to play or pause the music.
- Increase/decrease volume: Use one nger to slide
from the top to the bottom to decrease the volume
and vice versa to increase volume.
volume+/next track
volume-/previous track
microphone
3.5mm audio port
LED
micro usb port
multifunction button
Basic Operation
Powering on: Press and hold multifunction button for 3 seconds. Blue light
blinks 3 times and headphone beeps to indicate that power is on.
Answering a call: Short press multifunction button to take the call.
Ending a call: Short press multifunction button until headphone beeps.
Rejecting a call: Press and hold the multifunction button for two seconds
until headphone beeps.
Switching conversation from headphone to mobile phone: Press
multifunction button for 2 seconds, voice will be switched from headphone
to mobile phone and vice versa.
Redialing last dialed number: In stanby mode, press volume(+) button for 3
seconds until the beeping notification takes place.
Microphone mute: Press and hold volume(-) button for 2 seconds until the
headphone beeps. Press and hold volume(-) button for 2 seconds to
unmute.
Volume adjustment: short press volume(+) button to increase volume,
short press volume(-) button to decrease volume.
Play/Pause: Short press multifunction button can to play/pause music.
Forward/backward: Long press volume(-) button to play the last song, long
press volume(+) button to play next song.
Pairing mode: Deactivates automatically within 3 minutes when no device
is connected.
Auto power-off: SB270 will shut off automatically after 10 minutes of idle
activity.
Manual power-off: Press multifunction button for 6 seconds until red light
blinks 3 times and headphone beeps.
- Backward/forward: Use two ngers (the ngers
need to be spread out) to slide from the top to the
bottom to play the next song and vice versa for
previous track.
Features
Music play time: 14 hours
Talk time: 12 hours
Range: up 10 meters or 33 feet
Bluetooth standard: Bluetooth 3.0 +
EDR version with AVRCP and A2DP
Speaker: 40mm driver speaker x 2
Minimum voltage: 5V 200mAh
S undBot®
SB270
Quick Start Guide
&
User Manual
www.soundbot.com
experience audio excellence.
live the state of art technology.
feel the difference.
General Use and Notices
Please read the following information before using this product.
Users are not permitted to make changes or modify the product and the accessories in any way.
1. DO NOT use the product while operating a motor vehicle.
2. To avoid electronic interference and/or compatible conflicts, TURN OFF the product in any
facilities where posted notices instruct you to do so. For example: Aircraft, Military Base, Hospital
or Health Care Facilities.
3. To avoid impairing your hearing in the long-term operation, keep the headset volume in the
moderate level.
4. Keep away of fire, water, and high voltage equipment.
5. Follow the charging procedure described in this guide to charge the product.
Charging the Battery
SB270 uses a rechargeable battery. A normal charging process takes about 3 hours. The red LED
will turn on when charging and will turn off when charging is finished.
When the battery is nearly used up, the red LED will flash every 30 seconds and there will also be
a prompt from the headset. Please charge the headset at this time.
Please make sure the battery has been fully charged your first three uses to ensure the battery’s
best performance.
Always use proper AC Power Adapter (not included) to charge the headset. Using any incorrect
power supply device will cause damage and void the warranty.
Upon completion of charging, please pull out the cable from the headset t. Do not put the headset
in charging state past it being fully charged. This will shorten the lifetime of the battery.
Do not use the headset in extreme hot or cold environment. It is recommended to keep the
environment temperature between 15 and 25 degrees Celsius.
Do not install, place or use the headset near any source of heat such as a stove, radiator, oven,
toaster, coffee maker or other apparatus (including microwave oven) that gives off heat.
SoundBot® is a registered trademark of SoundBot.
Warranty and product info: http://www.soundbot.com
All trade names are registered trademarks of respective manufacturers listed.
Bluetooth technology and trademark are registered property of Bluetooth SIG.
All rights reserved.

Vraag over de SoundBot SB270?

Wanneer u een vraag heeft over de "SoundBot SB270" kunt u die hier stellen. Zorg voor een duidelijke omschrijving van uw probleem zodat andere gebruikers en/of de redactie u van een passend antwoord kunnen voorzien.

Koop gerelateerde producten: